A TEXTBOOK OF MACHINE DESIGN BY R.S.KHURMI AND J.K.GUPTA PDF

: A Textbook of Machine Design: Contents 1 Introduction 2 Engineering materials and their properties 3 Manufacturing considerations in machine. Veja grátis o arquivo A Textbook of Machine Design by AND J.K. GUPTA enviado para a disciplina de Elementos de Máquinas I Categoria: . A TEXTBOOK OF. (S.I. UNITS) [A Textbook for the Students of B.E. / , U.P.S.C. (Engg. Services); Section ‘B’ of A.M.I.E. (I)]. R.S. KHURMI J.K. GUPTA.

Author: Zulkidal Gorr
Country: Turks & Caicos Islands
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 3 October 2014
Pages: 244
PDF File Size: 14.50 Mb
ePub File Size: 15.94 Mb
ISBN: 966-8-54741-880-4
Downloads: 3333
Price: Free* [*Free Regsitration Required]
Uploader: Melrajas

The term viscosity index is used to denote the degree of variation of viscosity with temperature. It is the ratio of the diametral clearance to the diameter of the journal. The diametral clearance c in a bearing should be small enough to produce the necessary velocity gradient, so that the pressure built up will support the load.

When the length of the journal l is equal to the diameter of the journal dthen the bearing is called square bearing. Also the small clearance has vy advantage of decreasing side leakage. Because of the side leakage of the lubricant from the bearing, the pressure in the film is atmospheric at the ends of twxtbook bearing. The density at any other temperature t may be obtained from the following relation, i.

  HERMETICA WALTER SCOTT PDF

Machine Design Books

Minimum oil film thickness. McKee in an actual test of friction is shown in Fig. Attitude or eccentricity ratio. It is denoted by e.

A Textbook of Machine Design by AND [tortuka]_pdf – DocDroid

The average pressure will be higher for a long bearing than for a short or square bearing. It is the temperature at which an oil will cease to flow when cooled.

The bearing should not be operated at this value of bearing modulus, because a slight decrease in speed or slight increase in pressure will break the oil film and make the journal to operate with metal to metal contact. It is the minimum distance between the bearing and the journal, under complete lubrication condition.

If the ratio of the length to the diameter of the journal i.

Pour point or freezing point. However, space requirements, manufacturing, tolerances and shaft deflections are better met with a short bearing.

A Textbook of Machine Design by R.S.KHURMI AND J.K.GUPTA .0005

The thin film or boundary lubrication or imperfect lubrication exists between R and S on the curve. This will result in high friction, wear and heating. Enviado por igualdi flag Denunciar. The following terms used in hydrodynamic journal bearing are important from the subject point of view: Short and long bearing.

However, the allowance must be made for manu- facturing tolerances in the journal and bushing. This is the region where the viscosity of the lubricant ceases to be a measure of friction characteristics but the oiliness of the lubricant is effective in preventing complete metal to metal contact and seizure of the parts. A commonly used clearance in industrial machines is 0. It has been shown by experiments that the rr.s.khurmi of friction for a full lubricated journal bearing is a function of three variables, i.

  ELITA GSW PDF

It r.s.khurrmi the temperature at which an oil gives off sufficient vapour to burn it continuously when ignited. It is the lowest temperature at which an oil gives off sufficient vapour to support a momentary flash without actually setting fire to the oil when a flame is brought within 6 mm at the surface of the oil. It is the difference between the radii of the bearing and the journal.

It is the ratio of the eccentricity to the radial clearance. It the difference between the diameters of the bearing and the journal. It is denoted by h0 and occurs at the bu of centres as shown in Fig.