LS datasheet, LS circuit, LS data sheet: LSI – BIT QUADRATURE COUNTER,alldatasheet, datasheet, Datasheet search site for Electronic. LSI LS 30 available from 2 distributors. Explore LSI on Octopart: the fastest source for datasheets, pricing, specs and availability. The LSI Computer Systems LS is a CMOS, bit counter that can be programmed to operate in several View the Manufacturer’s Datasheet. Features.

Author: Dailkree Daikinos
Country: Sri Lanka
Language: English (Spanish)
Genre: Marketing
Published (Last): 6 December 2014
Pages: 46
PDF File Size: 18.22 Mb
ePub File Size: 6.41 Mb
ISBN: 615-5-82397-522-6
Downloads: 13689
Price: Free* [*Free Regsitration Required]
Uploader: Bazilkree

This c file contains various functions used to interface with the LS Note that to use thethe only steps are to setup the pins, call the init function, then call the read function to get a value. The LS communicates with a microcontroller via a bi-directional 8-bit data bus datzsheet several control bits. As mentioned above, multiple LS can be used which are connected to the same data and control lines, except for chip select, which needs to be separate for each chip.

Views Page Discussion View source History.

Alternatively, at each read the PIC could send back the actual count value. Because of this, if running the motor backwards continuously counting downthe value of CNTR will always be between 0 and PR at the current position.

Note that at the end of the init function, the counter limit value is loaded into the PR register. There are also two pins which output flags when programmed events occur, such as an overflow.

Note that most pins are active low, and thus must be kept at high at all times unless in use. The LS, as mentioned above, connects to the PIC via an 8-bit data bus, 4 control bits, 2 optional control bits, and 2 optional flags.


LS Datasheet(PDF) – LSI Computer Systems

The init function can be modified to utilize other special features of the chip not used here. Note that the code does not reset to 0 when it lls7166 PR.

Since this was put in the separate function, other code won’t have to be changed, other than TRIS setups. For instance, if the maximum count isand CNTR isthen the actual position is out of In any motor-related application, binary sl7166 is necessary. This c file simply loops continuously and reads values from the LS Personal tools Log in. Retrieved from ” http: Eventually the CNTR will overflow if not reduced.

For more info on these features, see the datasheet. The value of the PR register is loaded whenever the counter borrows downticks from 0.

Selling LST, LS, LS with LST, LS, LS Datasheet PDF of these parts.

All three can be download from this zip file. The A and B inputs normally serve as quadrature inputs, like those which come from a quadrature encoder like those on most motors.

Using a parallel data bus, a microcontroller can simply read the current count value from the chip, allowing a project to interface with motor encoders without using any additional timers.

Most other functions will usually not be needed unless special features are needed. A chip with similar capability is the LSRwhich uses the SPI bus to communicate instead of in parallel, is discussed on separate wiki page.

Using the LS7166 Quadrature Counter

This is useful for motor applications, since the fixed value can be set to the number of pulses in a full rotation, and then whenever the count value is read, the exact position of the motor can be known no matter the amount of time that has passed since the last read.


Because of this, the pic software must be written so that the read value of CNTR is modded by the maximum count number to find the position. The chip can also operate in divide-by-n mode, which loads the count register with a fixed value on rollover. The chip has several other features that can ls7166 read about in the datasheet.

The LS is a 24 bit quadrature counter.

LS709T, LS7100, LS7166

In the code below and example schematic, pins B0-B7 are used for the data bus. This number should be changed based on the full rotation count of the encoder in daasheet. These pins can be changed, but the data bus read and write functions will need to be changed to interface with bit lines instead of bytes. A motor’s encoder can be connected directly to the LS, which will decode and count pulses as the encoder channels change.

The following is a list of registers and the general use of each, even though they are already handled by the code written in a later section. The code in this document only covers divide-by-n binary quadrature mode, and for more advanced features the support code will need to be modified.